Handguard Sword - Part Two

Handheld Small Sword Part Two

• Pocket-sized, highly playable, the heavy sword body only requires 50 grams of filament. Note that the support at the pointed corners should be shortened and the wrapping part should be removed first, remove the large supports and then remove the small supports wrapping the pointed corners! Be careful not to break the handle support when removing it.

  This content can be used as a handheld item or a children's toy. The displayed printing material is AILEKU golden silk PLA (not recommended, too brittle, Tianrui or TuZhu's golden printing effect is better!), the default parameters are “layer height 0.2, tree support slender tree, threshold 30, top support layer 4. bottom support layer 4, Support removal difficulty 1 star.

  Please adjust the material temperature before printing, if you have any questions, you can discuss in the comment area, welcome all bigwigs to return pictures and comments! Thank you all!!!

   

• Size can be scaled according to personal preference,it is recommended to use PLA material for printing, the effect will be more delicate!
• Default parameters can also be used for printing, those who have high requirements can fine-tune them themselves
• Personal experience: When disassembling the support, remember to use ingenuity to remove it in the direction you need to remove, be sure to cut off the support part away from the support contact surface first, leaving just enough for the jaws of the pliers to open, so you can just clamp the tip of the support at the level closest to the model, the pliers rolling method ---- When clamping the support close to the model's layer, using the pliers to roll and tear, you can probably roll up the support layer to be removed, pay attention to adjusting the hand fixation posture, be patient, proceed step by step...

• 3D Printing Tips and Precautions

• (All models published by this account have been test-printed and can adapt to all models. Before printing, you need to check whether the printer and filament are normal. If you encounter problems that cannot be solved, please feel free to send me a private message, and I will try my best to help you solve them!
• Precautions:
• You can go to Reference learning area:Print Quality and Troubleshooting | Bambu Lab Wiki
• Ensure that the machine's printing plate is clean. It is recommended to wipe it with 95-degree medical alcohol after each print to ensure stable print quality and prevent failures.Because the oil residue on your hands after touching the print panel will greatly reduce the adhesion of the print, and the small debris and residues from previous prints will also affect the quality of the first layer, thus reducing the yield.
• Pay attention to filament drying (PLA generally does not need drying, basically good moisture resistance), this will greatly affect your print quality and printing experience! Filaments will inevitably become damp after being stored for a long time, if stringing and spaghetti occur, you need to ask the merchant to consult the drying parameters and printing parameters for adjustment,Most merchants' filaments are not dried before leaving the factory, so if conditions permit, pre-drying can be done, and the printing effect will be better.
• The choice of printing material, appearance parts generally use PLA, structural parts generally use PEGT, the prices of these two materials are relatively affordable and the emission of toxic gases is almost zero. (For health, it is best to have an air purifier running)
• When using new filament, it is recommended to carry out filament flow calibration immediately, and modify the calibration coefficient, this will greatly affect your print quality, and is a necessary process for the new filament to adapt to your printer.
• If you encounter problems such as a sudden drop in print quality and low yield, check for nozzle clogging, check if the printer is placed steadily (it is more reliable to place it directly on the ground), you can also try recalibrating the printer.
• Print at the recommended printing speed in the model instructions. Overhang quality, the number of model surfaces and printing speed are directly related, the appropriate speed (too fast or too slow is not good) allows the material to have more time to cool and form during deposition.
• Set the hot bed and nozzle temperature reasonably according to different materials.Too high or too low temperatures can cause warping, layer deformation or adhesion problems, thus affecting print quality and success rate. For P1S models and above, if the temperature inside the user cabin exceeds 35 degrees, be sure to open the glass door of the machine body.

Sword

Warcraft

Toy

Weapon

COSPLAY