POPNAS Four-Bay Modular Hard Drive Enclosure V1

POPNAS四盘位模块化硬盘仓V1

【尺寸】132x184x218
【材质】增强型PETG
【硬盘位】3.5寸机械硬盘X4 
【电源】需要Flex、1U电源，也可以直连nas的IDE线。
【背板】星际蜗牛B款背板，四盘位，单IDE，支持热插拔。
【数据传输】支持SATA转typeC转接板。JM575、JM580。使用此方案，需要配一根typeC转USB线，用来连NAS的后置USB。
【SATA数据线】四根直头转正弯。若NAS有空位，可以直接连NAS。长度根据实际需求考虑。
【散热风扇】前后双12015风扇，需要一根额外的IDE转4pin线。
【开关】24pin短接开关一根

【其他配件】硬盘减震螺丝 24颗、固定JM575或JM580 typeC转接板 M3X10内六角平头螺丝螺母 三颗，固定电源所需内六角平头螺丝 M3X12，固定硬盘仓所需内六角平头螺丝M3X10 四颗、3mmX3mm N52铷磁铁 四颗、固定风扇螺丝螺母 M4X30 八颗。

此硬盘仓设计不可商用，特此声明。

• Dimensions: 132x184x218 (unit not specified, typically mm for such products)
• Material: Reinforced PETG (PETG: Polyethylene Terephthalate Glycol, a common thermoplastic with good impact resistance and processability)
• Hard Drive Bays: 4 x 3.5-inch HDDs (HDD: Hard Disk Drive, mechanical hard disk)
• Power Supply: Compatible with Flex power supply, 1U power supply; can also be directly connected to the NAS via IDE cable.
  (Note: IDE is an older parallel interface for storage devices, less common in modern NAS; "直连 nas 的 IDE 线" may refer to connecting via an IDE cable compatible with the NAS)
• Backplane: Xingji Woniu Model B Backplane, 4-bay, single IDE interface, supports hot-swapping.
  (Hot-swapping: The ability to insert/remove hard drives without powering off the device)
• Data Transfer: Supports SATA-to-Type-C adapter boards (e.g., models JM575, JM580). For this setup, a Type-C-to-USB cable is required to connect to the NAS’s rear USB port.
  (SATA: Serial Advanced Technology Attachment, the mainstream serial interface for modern hard drives/SSDs; Type-C: a universal USB connector standard)
• SATA Data Cable: Straight-to-right-angle connector. If the NAS has an available slot, it can be directly connected to the NAS. Length should be selected based on actual needs.
• Cooling Fan: Dual 12015 fans (front and rear) (12015: A common fan size, 120mm in length, 15mm in thickness). Requires one IDE-to-4-pin cable (for powering the fans).

• Switch: One 24-pin shorting switch cable (24-pin: A common power connector standard for motherboards; a shorting switch is used to trigger power-on/off by shorting specific pins).

  【Other Accessories】：

• 24 pieces of hard drive shock-absorbing screws
• 3 sets of M3×10 hexagon socket flat head screws and nuts (for fixing JM575 or JM580 Type-C adapter boards)
• Hexagon socket flat head screws (M3×12, for fixing the power supply)
• 4 hexagon socket flat head screws (M3×10, for fixing the hard drive bay)
• 4 pieces of 3mm×3mm N52 neodymium magnets (N52: A grade of neodymium magnet representing high magnetic strength)

• 8 sets of M4×30 screws and nuts (for fixing cooling fans)

  Note: This hard drive bay design is not authorized for commercial use. This is hereby explicitly stated.