Disney Inspired Villain Lantern

A fully printable lantern with 10 different interchangeable lantern panels based on Disney's infamous Villain line-up including Hades, Dr. Facillier, Jafar, Maleficent, The Evil Queen, Ursula, Cruella, Queen of Hearts, Oogie Boogie and The Chernabog. All printable on a multi or single colour printer.

The lantern has 4 windows for the interchangeable panels and attaches to the roof using 4 corner clips that are also printable separately. It prints in 5 parts with no supports needed, except for the large roof piece, which should be printed with regular (non tree) supports, pointy side facing upwards. In order to stop the light from escaping dark filament is recommended, preferably with 3 or 4 walls instead of Bambu's usual 2 wall settings.

The lantern comes fitted with a wire groove in the bottom to lay flat on any surface and also has a hole in the top for easy hanging. It fits Bambu's led lamp kit 001, but for those who don't have the light an electric tealight holder adapter is also included that can be slotted into the base.

It can be permanently attached together using glue, which is optional (Mainly if you plan to hang it), but unless you plan to keep the same 4 panels do not glue the top panel border where the clips are as you won't be able to change panels afterwards. Assembly is fairly straightforward but if you need any help feel free to drop me a message

Panels & HueForge instructions

Hades

Swap Instructions:

Start with Turquoise

At layer #4 (0.28mm) swap to Cyan

At layer #19 (0.88mm) swap to Cobalt Blue

At layer #35 (1.52mm) swap to Black for the rest.

Jafar

Swap Instructions:

Start with Sunflower Yellow

At layer #12 (0.6mm) swap to Pumpkin Orange

At layer #18 (0.84mm) swap to Red

At layer #40 (1.64mm) swap to Black for the rest.

Queen of Hearts

Swap Instructions:

Start with Jade White

At layer #4 (0.28mm) swap to Red

At layer #19 (0.88mm) swap to Pumpkin Orange

At layer #21 (0.96mm) swap to Black for the rest.

Chernabog

Swap Instructions:

Start with White

At layer #7 (0.4mm) swap to Grey

At layer #22 (0.56mm) swap to Black for the rest.

Mal

Start with Yellow

At layer #9 (0.48mm) swap to BambuLab Green

At layer #24 (1.08mm) swap to Black for the rest.

Oogie

Swap Instructions:

Start with Jade White

At layer #5 (0.32mm) swap to BambuLab Green

At layer #19 (0.88mm) swap to Dark Green

At layer #30 (1.24mm) swap to Black for the rest.

Ursula

Swap Instructions:

Start with Jade White

At layer #9 (0.48mm) swap to Magenta

At layer #13 (0.64mm) swap to Cobalt Blue

At layer #22 (1mm) swap to Black for the rest.

Dr. Facilier

Swap Instructions:

Start with Jade White

At layer #10 (0.52mm) swap to Purple

At layer #20 (0.92mm) swap to Indigo Purple

At layer #27 (1.2mm) swap to Black for the rest.

Evil Queen

Start with Jade White

At layer #13 (0.64mm) swap to Purple

At layer #26 (1.16mm) swap to Indigo Purple

At layer #28 (1.24mm) swap to Black for the rest.

Cruella

Swap Instructions:

Start with Jade White

At layer #8 (0.44mm) swap to Red

At layer #17 (0.8mm) swap to Maroon Red

At layer #23 (1.04mm) swap to Black for the rest.