Bambu A1 poop Bin

Here is my version of the poop bucket for my Bambu Lab A1
I wanted it to be large enough, high enough on the side to stop projections and for it to have a side flap on the right to prevent droppings from passing under the bed, I put two places for magnets so that It remains attached to the printer's foot, and finally I added the Bambu Lab logo... because it's one of my first prints and I wanted to do multi-color.
Well I hadn't received my green filament yet so I put white and I find that it looks great on gray, but you can use the color you want ;-)

I printed it in a layer of 0.20 so that it would be better finished but those in a hurry can use a layer of 0.28 to print it in less than 5 hours.

External dimensions :
- Height: ~120 mm
- Length ("along" the printer): ~230 mm
- Width: ~128 mm
- thickness: 1,6 mm

Here is a (New) Smaller version:

And a brand new version attached to the printer:

Here is my Optimized Poop Deflector:

Find all my accessories for your printer here:

>> 2024-11-23 <<

Added a background to the back of the logo and increased the thickness of the side flap

>> 2024-08-13 <<
Following a user's judicious remark, I put the Bambu Lab logo back on the right side, first design on Makerworld, rookie mistake

I also put it in hollow rather than in over-thickness to improve aesthetics, time and filament .

>> 2024-05-26 <<
There are now 2 versions:
1 - for the A1 without accessories
2 - for the A1 with Stiffener (AMS mounted on the printer)

I put each model on 1 plate, that way you will have both and you can choose the one you want.

- Slight changes in dimensions, thickness reduced to 1.6 mm, this saves material and printing time, despite everything the solidity is sufficient.
- Layer height 0.28 for the same reasons (you can reduce to 0.20)
- I increased the angle of the side flap which had caused problems for some people, so that it prints better.
- Reduced the thickness of the logo which was sticking out a little too much.
- Location for larger magnets: diameter 8, thickness 2 mm (use strong neodymium N52 so that it remains attached to the printer)

______________________________________________________________________________________________________________________________________________

Here is my version of the poop bucket for my Bambu Lab A1
I wanted it to be large enough, high enough on the side to stop projections and for it to have a side flap on the right to prevent droppings from passing under the bed, I put two places for magnets so that it remains attached to the printer's foot, and finally I added the Bambu Lab logo... because it's one of my first prints and I wanted to do multi-color.
Well I hadn't received my green filament yet so I put white and I find that it looks great on gray, but you can use the color you want ;-)

I printed it in a layer of 0.20 so that it would be better finished but those in a hurry can use a layer of 0.28 to print it in less than 5 hours.

External dimensions :

- Height: ~120 mm

- Length ("along" the printer): ~230 mm

- Width: ~128 mm
- thickness: 1,6 mm

Here you can find a (New) Smaller version:

And a brand new version attached to the printer:

And here is my Optimized Poop Deflector:

Find all my accessories for your printer here:

>> 2024-11-23 <<

Added a background to the back of the logo and increased the thickness of the side flap

>> 2024-08-13 <<

Following a user's judicious remark, I put the Bambu Lab logo back correctly, first design on Makerworld, rookie mistake

I also put it in hollow rather than in over-thickness to improve aesthetics, time and filament.

>> 2024-05-26 <<
There are now 2 versions:
1 - for the A1 without accessories
2 - for the A1 with Stiffener (AMS mounted on the printer)

I put each model on 1 plate, so you will have both and you can choose the one you want.

- Slight modifications to the dimensions, thickness reduced to 1.6 mm which saves material and printing time, despite everything the solidity is sufficient.
- Layer height 0.28 for the same reasons (you can reduce to 0.20)
- I increased the angle of the side flap which had caused problems for some people, so that it prints better.
- Reduced the thickness of the logo which was sticking out a little too much.

- Location for larger magnets: diameter 8 thickness 2 mm (use strong neodymium N52 so that it remains attached to the printer)