Zoidbergererer

cover

IMG_5584.jpg

IMG_5583.jpg

IMG_5582.jpg

IMG_5581.jpg

IMG_5580.jpg

IMG_5631.jpg

plate_1.png

2024-08-13_27424ffce4033.jpg

2024-08-13_05e6e1b6f120f

0.2mm layer, 2 walls, 15% infill

Skeleton articulated keychain 8 pack plate

CipherX.xyz

skeletonkeychain.jpg

skeletonkeychain2.jpg

8 Pack Plate - Remixed Articulated Skeleton Keychain reduced to 40% original size- 0.2mm layer, 2 walls, 15% infill&nbsp;<h3>3D Print Profile:</h3><ol><li>Scale and Layout:<ul><li>Scale: Scale the original model to 40%.</li><li>Quantity: Fit 8 skeleton keychains on the print bed.</li><li>Arrangement: Use a 3x3 grid-one top right corner for speed arrangement to ensure they fit comfortably within the 256x256 mm build plate.</li></ul></li><li>Material:<ul><li>Filament: Use PLA or another preferred filament for keychain durability.</li></ul></li><li>Layer Height:<ul><li>0.20 mm layer height for a balance between speed and detail.</li><li>0.12 mm if higher detail is required for the skeleton joints and skull.</li></ul></li><li>Infill:<ul><li>Infill density: 10-15%. Since the keychain doesn’t need much internal strength, a light infill will work well.</li><li>Infill pattern: Grid or gyroid for faster print speeds and good strength balance.</li></ul></li><li>Perimeters:<ul><li>Perimeters: 2-3 perimeters (shells) to ensure the skeleton parts are durable enough for movement but don’t take too long to print.</li></ul></li><li>Supports:<ul><li>Support: NO SUPPORT NEEDED</li></ul></li><li>Build Plate Adhesion:<ul><li>Brim: Add a brim (5 mm) for small parts like the skeleton joints to prevent warping and ensure they stay on the bed.</li><li>Adhesion Type: Use a brim or skirt based on the printer's bed adhesion capability.</li></ul></li><li>Print Speed:<ul><li>Base Layer: Print the first layer slowly for good adhesion.</li><li>Subsequent Layers: Increase spee for the rest of the print, depending on the complexity of the parts.</li></ul></li><li>Cooling:<ul><li>Enable cooling after the first layer to prevent deformation in smaller parts.</li><li>Fan speed: Set the fan speed to 100% after the first layer for PLA.</li></ul></li><li>Retraction:<ul><li>Retraction distance: 1-1.5 mm (for direct drive extruders like on the Bambu Lab printer).</li><li>Retraction speed: Set to 30-35 mm/s to reduce stringing.</li></ul></li><li>Post-Processing:<ul><li>Optionally, you can apply a light initial movement to each joint area, to ensure smooth movement.</li></ul></li></ol><h3>Key Points:</h3><ul><li>Scaling and Fit: At 40% scale, fitting 9 keychains in a 3x3 grid layout on the 256x256 mm plate is feasible.&nbsp;</li></ul>

Remixed Articulated Skeleton Keychain 8 Pack Plate

Articulated skeleton model prints without supports. Thought it&#39;d be fun to create an early Halloween ornament. A friend mentioned I should put magnets in the back of the head for a fridge ornament which would be fun. Sits nicely on a shelf or wiggles / shakes it&#39;s articulated bones.

Articulated Skeleton Halloween Ornament Decoration

ASIA

Print Profile(2)

Description

Comment & Rating (34)

License

Related Models