Race Mount Bikerwardrobe

Search models, users, collections, and posts

PRINTNIC

Hobby & DIY>Other Hobby & DIY

IP Report

Print Profile(3)

All

P1S

P1P

X1 Carbon

X1E

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

0.2mm layer, 3 walls, 25% infill PLA

Designer

31.5 h

5 plates

5.0(7)

0.2mm layer, 3 walls, 10% infill PETG

Designer

29.9 h

5 plates

4.9(7)

0.2mm layer, 3 walls, 10% infill PETG-CF

Designer

29.9 h

5 plates

5.0(4)

Open in Bambu Studio

Boost

459

1057

706

198

Released

Description

Hello my Friend and Welcome to my Page :) Have Fun with the choosen Model and let me know what you think after Printing it in the Comments. I appreciate every Feedback and hope you find something usefull for yourself. Enjoy

The Wardrobe for every Biker! A must Have!

Fellow Bikers, You and I know the Struggle.. Paying 1000s of Dollars for our Lovely Helmet and Leatherkombis.. But.. No one see´s them when we dont wear them. Also, they take up so much Space in the Closet. So here comes my Solution for this Problem.

The RACE MOUNT

Boost Me (for free)

If you Like my Work, Please show some Makes, give a like and if you want to, a little Boost :) I Appreciate every Single one

I spend half a Year to figure out the Perfect Solution which is Eyepleasing, Easy to Print and Holds my Helmet, Keys and the Rest of my Bikewear. Here are some Informations about my Design and what Features it brings to the Table :)

RACE MOUNT is a Bikerwardrobe which can Hold your Helmet, Your Jacket or Leatherkombi and, of Course, Your Precious Keys.

Its Designed for a Minimalistic look and at the same time, to get the most Use out of it as possible. I wanted it to be Leightweight but Sturdy, Usefull but looking good. A little Technical too.

Installation Guide:

First of, you need some Non 3D Printed Parts. The List below is Everything you need besides the 3D Printed Parts.

10x M3 Washers 6.5mm Diameter
10x M3 Threated inserts
6x M3 x12 Screws
4x M3 x25 Screws

I Printed mine in PETG-CF for Max Durability. You will need around 1,3 Kg of Filament for this Print. Also, Make sure your Printplate is Clean, all around, also the Edges. The Mainframe and the Kombihook takes almost the Complete Buildplate close to the edge. So, make sure that thing is Clean to geht good Bedadhession.

Lets Start the assembly:

All 3D Printed Parts and the Screws needed (Heated inserts are already melted in)

Threated Inserts mounted in the Mainframe and the Kombihook

Snap the Mainframe in the Backplate, its a tight Fit. Make sure to remove all the Supports!

Take the 6 M3 x12 Screws, Put one washer on each of them and screw them in. Be Carefull not to tightem them to Hard!

Time to Mount the Kombihook under the Mainframe. Same as the Backplate. Use 4 M3 x25 Screws with Washers to mount it.

Time to put it on the Wall :) The Keysafe can be filled with Keys, Transmitters or even the Paperwork for your Bike.

Just put the Keysafe it in the Mainframe when filled. Its a relatively tight fit. it Stays in Place but is also Easy to remove.

Mount it to the Wall: Depending which Wall you have you will need 4 Dowels to mount it. Dont tighten the 4 Screws to tight. They can Easily Rip trough the Plastic when to tight. And voillah, there is your new Bikerwardrobe.

Use the included Markingtemplate to Drill the Holes in the right Spacing

Now youre Ready to Go :) or better, Ready to Rest and have your Bikewear Sorted and stored nicely. Have Fun Printing and leave a Like, A Comment/Make and, if you want to, a Boost. I appreciate it

Comment & Rating (71)

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.