Pliers Rack / Holder / Organizer - IKEA Skadis - Free 3D Print Model

Search models, users, collections, and posts

ShopTeacher

Tools>Hand Tools

IP Report

Print Profile(3)

All

X1 Carbon

P1S

P1P

X1E

H2D

H2D Pro

H2S

P2S

H2C

X2D

A2L

A1 mini

Plier Racks -All sizes- 3 Walls - 15% Gyroid - Tree Supports

Designer

25.7 h

8 plates

4.9(464)

Medium size, 3 hole @ 0.2mm layer, 3 walls, 12% infill

1.9 h

1 plate

4.9(76)

0.2mm layer, 3 walls, 15% infill

1.6 h

1 plate

4.9(16)

Open in Bambu Studio

Boost

1737

6795

697

275

7.1 k

4.6 k

Released

Description

Non-IKEA Skadis pliers rack with 2 screw bosses for mounting: https://makerworld.com/en/models/749672#profileId-683174

Pliers racks are available in for small/medium sized pliers handles and large/extra large sized pliers handles. Each size has 3, 4, 5, and 6 pack options.

Special thanks to 3DTechBase (https://makerworld.com/en/@3DTechBase) for requesting the IKEA Skadis version of this model and supplying the model images.

Comment & Rating (697)

@3DTechBase

Boosted

Pinned by Designer

Print Profile

Plier Racks -All sizes- 3 Walls - 15% Gyroid - Tree Supports

Thank you! If you want you can use my picture. 🙂

The profile uploader has replied

@ShopTeacher

thanks so much. i appreciate the offer and will take you up on it.

(Edited)

@3DTechBase

Boosted

Replying to @ShopTeacher :

You are very welcome! I thank you for the quick response! 🙂

(Edited)

@ShopTeacher

Thanks for the boost!

(Edited)

@Krakers

Print Profile

Plier Racks -All sizes- 3 Walls - 15% Gyroid - Tree Supports

Some supports failed on my a1 mini, so I think they should be slowed down, but still usable. Good design

(Edited)

The profile uploader has replied

@ShopTeacher

i wish bambu studio had an option to slow down support printing. you can slow it down for overhangs, walls, infill... but not supports. otherwise you would have to run it in silent mode or adjust your filament settings. possibly need to scrub the bed with soap and water?

@Krakers

Replying to @ShopTeacher :

Actually there is an option to control speed of printing supports - you go to "speed" tab, mark "advanced" and then you can set speed for "supports". You could also make supports use two wall loops for additional stability (supports tab) or use "slow down by height" ("speed" tab) especially for bedslingers. My bed was cleaned with soap just before this print, but when it comes to this skadis hooks it often causes this problem for my a1 mini. No such problem exist for my x1c

(Edited)

@ShopTeacher

Replying to @Krakers :

thanks for the tips. ill check them out

(Edited)

@clinpath

Boosted

Print Profile

Plier Racks -All sizes- 3 Walls - 15% Gyroid - Tree Supports

Two of the supports for the attachment pegs randomly came loose early in printing. I kept a close eye on it and it mostly recovered. Those two pins are a bit short and a little wonky but for this size pliers rack, there are plenty of pins across two rows so it still attaches securely to the pegboard. A+ for redundancy in the connector pins! Printed on an A1 with Polymaker PLA Pro. Pic shows it holding a set of mini pliers and cutters from Harbor Freight.

The profile uploader has replied

@ShopTeacher

I have printed quite a few of these for home and work and have had that happen as well. Its fairly rare and the tree supports seperated from the bed when it happened to me.

(Edited)

@clinpath

Boosted

Replying to @ShopTeacher :

Same, the rightmost (when looking at the rack as installed) trees came off the bed. It happens! I don’t generally have adhesion issues, but when I do, it’s often with Polymaker filament. I probably need to continue to tweak the settings. Thanks for a great design!

@ShopTeacher

Replying to @clinpath :

thanks for the boost. take care

@user_457726814

Print Profile

Plier Racks -All sizes- 3 Walls - 15% Gyroid - Tree Supports

Works well

The profile uploader has replied

@ShopTeacher

fancy

@3CopyCatD

Print Profile

0.2mm layer, 3 walls, 15% infill

Quick print for the size.

The profile uploader has replied

@Digital_Smiley

Thank you

@DuckyLove90

Boosted

works well🤙

The designer has replied

@ShopTeacher

Nice setup. thanks for the boost!

@Matt_yz125

Print Profile

0.2mm layer, 3 walls, 15% infill

great print!

@many_layers

Boosted

Printed great. Works perfectly! Thanks!

The designer has replied

@ShopTeacher

Thanks for the boost!!

@deathraylabs

Boosted

i love this model, looks great and works great for my needs. thank you for sharing this work!

The designer has replied

@ShopTeacher

Thanks for the boost!

@650101965

Boosted

Print Profile

Medium size, 3 hole @ 0.2mm layer, 3 walls, 12% infill

Low profile, easy to access and holds my larger tool. Easy to access. Really nice print!!

@ShopTeacher

Thanks for the boost

@LarsaDehlin

Print Profile

Plier Racks -All sizes- 3 Walls - 15% Gyroid - Tree Supports

Perfect print profile. Somewhat tight fit in the Skådis board but i just cut a part of the tip of the hooks and voila, it fits.

The profile uploader has replied

@ShopTeacher

the printed skadis boards have slightly smaller holes than actual skadis boards

License

This user content is licensed under a Standard Digital File License.

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.