Matthew Ghost

cover

plate_1.png

plate_2.png

2024-12-17_6385729385dcc.png

0.2mm layer, 2 walls, 15% infill

1.png

A1 Mini (0.2mm layer, 2 walls, 15% infill)

PXL_20241219_043911385.RAW-01.MP.COVER.jpg

PXL_20241219_043303855.RAW-01.COVER.jpg

PXL_20241219_043921582.RAW-01.COVER.jpg

<ul><li>1 Plate with print by object. The legs and case are printed as one object.</li><li>Swapped back to the case color for the panel and dials.</li><li>Added indicators to the ends of the dials.</li><li>Added pieces in the slicer to make this printable without support, which saves a bit of time and filament.</li><li>Added lots of ventilation to the back.</li><li>Rotated two of the legs so the surface finish is the same between the left and right.&nbsp;I used onshape to quickly make the triangle dials and hex cutout, and did all the rest with slicer tools, so you can remove any/all of these to get back to the original model if you don't want any of these changes.</li></ul>

no supports, 1 plate, ventilation, panel/dial colorswap

MacieG

IMG_0994.jpg

image (2).jpg

Modified enclosure with rear ventilation holes to allow better airflow for accurate temperature and humidity readings.

Ventilated Cover - 0.2mm layer, 2 walls, 15% infill 2 plates

Modified enclosure with rear ventilation holes to allow better airflow for accurate temperature and humidity readings.Single Plate Profile for AMS to save time on print preparation.

Ventilated Cover - 0.2mm layer, 2 walls, 15% infill, 1 plate

One (A1M Compatible)

Two (Not A1M Compatible)

RevHazlett

20250305_202939.jpg

Screenshot 2025-03-05 203904.png

20250305_202044.jpg

20250305_202123.jpg

20250305_202153.jpg

<ul><li>Rebuilt the face component from the author&#39;s STEP file to remove overhangs along three edges and shorten their length on the fourth.</li><li>No supports are required.</li><li>No brims are required if you have a clean build plate.</li><li>Whipped up a little antenna (glues together and in place). The more acute antenna goes on the offset side of the dome.</li><li>Carved out little squares for an accent color on the dials.</li><li>All components are addressable as objects in the slicer, so they can have their materials changed without painting.</li><li>Organized to print by object. Plate 1 is A1 Mini compatible and prints one, Plate 2 is not A1 Mini compatible but prints two.<ul><li>Either plate requires only five material changes!</li></ul></li><li>Back of the main body is printed without top or bottom surfaces to create a ventilation grille. This pattern and it&#39;s density can be changed if desired.</li><li>Consideration for line widths, infill angles and patterns, etc for a clean and unique finish.</li><li>Legs screwed in much easier than the original one I printed.</li></ul>Depending on your hygrometer&#39;s clips, it might be a tiny bit loose. I&#39;ve tried three different models in this print and one was a bit loose but still required prying to be removed.

Reduced Overhangs, Parts, Added Antenna - PLA on tPEI

askelias

IMG_8262.jpg

IMG_8276.jpg

IMG_8278.jpg

swivel tv.png

Drawing inspiration from another Hygrometer stand and born out of the annoyance that appears when it&#39;s a on a slight angle and you can&#39;t see the temp/humidity.  Remodeled to have more holes in the back and a bit slimmer to compensate for the filament that it adds with the stand. Still 30g, still 1h 40m to print. Still a super nice original design!

Swivel Stand Mod 0.16mm

TrD Office

IMG_8971.jpeg

IMG_8959.jpeg

Retro Print Gif.GIF

Multicolor Print with one time filament change on 1 Plate.The legs are also orientated for Plate Surface Texture to look same.

Multicolor; Single Plate; Single Filament Change

printer mayhem

IMG_0563.jpeg

2024-12-19.png

IMG_0564.jpeg

.20mm layers%15 gyroid infillprint by object

0.2mm layer, 2 walls, 15% gyroid infill, print by object

Jacob

Schermafbeelding 2024-12-18 183310.png

• P1S/P1P/X1C• 0.20mm layer height; • infill densilty 15%;• infill gyroide&nbsp;

0.2mm layer, 4 walls, 15% infill

Screenshot 2025-01-27 at 08.08.20.png

IMG_8962.jpeg

copy_981B48C8-EB1C-428B-98C6-649881F1BFCB.GIF

3 Copies in 1 Plate; MultiColor; 1 Time Filament Change

Screenshot 2025-01-25 at 22.46.10.png

2 Copies on 1 Plate; MultiColor; 1 Time Filament Change

#Skywa2804

tempImage6xJpV1.jpg

tempImageeGkOCo.jpg

Applied ironing to black front cover for better looks (see pictures)<ul><li>0.2mm layer</li><li>2 walls</li><li>15% infill</li></ul>

Ironed Black front + rear ventilation 

Lucyna Kushinada

PXL_20250124_124113018.jpg

<ul><li>0.2mm layer</li><li>3 walls </li><li>10% infill</li></ul>I use ABS.

by Object - one Plate - 0.2mm layer, 3 walls, 10% infill

You shall not share, sub-license, sell, rent, host, transfer, or distribute in any way the digital or 3D printed versions of this object, nor any other derivative work of this object in its digital or physical format (including - but not limited to - remixes of this object, and hosting on other digital platforms). The objects may not be used without permission in any way whatsoever in which you charge money, or collect fees.

This user content is licensed under a Standard Digital File License.

📺Decorative stand for Hygrometer / Thhermometer that fits in every home! Simply insert the thermometer into the hole in the retro TV.. Insert the face into the case and secure with the legs! So simple 😎.🔋When replacing the battery, the face can be slid out of the case. Push the face out using a thin object through the threaded hole for the leg.

Thermometer Hygrometer Stand – Retro Television

ASIA

Print Profile(14)

Bill of Materials

Description

Trophy Builder - Design & Print your Own Medal or Cup🏆 More Info Here 👇

Comment & Rating (594)

License

Related Models